Top 10 typical forklift crashes ， forklift procedure must take notice of these issues ！.

Top 10 typical forklift crashes ， forklift procedure must take notice of these issues ！.

Blog Article

Don't underestimate the forklift at the workplace. If the procedure is not good, there will be major mishaps in minutes, and there are several accidents involving forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a rolling accident.
Case 2: In order to maintain the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which practically caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not notice the pedestrian, and the pedestrian did not see the forklift.
Situation 6: The forklift lifts the personnel unlawfully, the forklift motorist does not wear the safety belt, the forklift lifter drops and the chauffeur is squashed when the forklift surrender.
Case 7: The forklift driver did not put on a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift procedure should pay attention to these issues ：.

Begin.
1. Prior to beginning, observe the surroundings, and after validating that there are no challenges that prevent the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge must be risk-free prior to starting.
3. When the forklift begins with a tons, the vehicle driver must initially verify that the lots is stable and reliable.
4. The start must be slow-moving and consistent.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast must be slanted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be issued first. High-speed doglegs are prohibited. High-speed sharp turns will trigger the automobile to shed side stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to switch off the fire and slide, and it is restricted to brake all of a sudden while driving with tons unless there are unique scenarios.
6. When the forklift is running, it has to obey the traffic rules in the factory and should keep a specific security range from the automobile ahead. .
7. When the forklift is running, the tons needs to remain in the most affordable setting that does not impede the driving, and the gantry must be effectively slanted back. The tons will not be increased except when stacking or loading. .
8. The height of the load must not obstruct the vehicle driver's view. In unique scenarios, when the product impacts the forward vision, drive at a low speed when turning around.
9. It is restricted to activate the ramp, neither to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility location is 5 km/h, and it should drive safely at a low rate when going into the production workshop area. .
11. When the forklift is raised, raised or driven, it is forbidden for employees to depend on the fork to hold products and play a stabilizing duty. .
12. If issues are found, they will be fixed and reported in a timely manner, and they will certainly never operate with ailments or hide them.

loading and dumping.
1. When fork-loading products, the range between both forks must be adjusted as required to make the tons of the two forks well balanced and not skewed, and one side of the thing must be against the shelf. .
2. It is forbidden to collaborate with a single fork or use a fork top or draw. In special conditions, security indication need to be set up to remind surrounding pedestrians. .
3. In the process of packing and unloading products, the forklift must be stopped with the brake. .
4. The speed of the automobile should be sluggish and steady. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled items and hurt people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it must be kept in mind that the fork suggestion must not touch other products or things. The load must be maintained with minimal back tilt of the gantry to make sure that the load does not move in reverse. The pole can be tilted ahead a little when the load is reduced to permit easy placement of the tons and removal of the forks. .
6. It is forbidden to fork goods at broadband and ram hard objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to stand around the fork, so as to prevent the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is restricted to utilize forks to raise employees to engage in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not permitted to make use of the brake inertia to slide, place, round or roll objects. .
10. It is not allowed to use forks to pick, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you need to discharge the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is cut off. (Except for special circumstances, such as the chauffeur does not leave the car's line of sight and does not exceed 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look ought to be inspected, and fuel, lubricating oil and air conditioning water need to be included.
2. Inspect the security performance of starting, running and stopping.
3. Inspect whether the lights and horn signals are total and effective.
4. During the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leakage ought Stand-on Electric Pallet Stacker to also be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine before leaving the automobile;.
2. When you experience a person before you during driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be also sharp to avoid the tendency of " cost-free turning";.
6. Adding and down the slope should be slow-moving and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the automobile should be driven in reverse when going downhill;.
8. When the forklift employees carry the goods and move on, if they run into big or hefty goods and most likely to the driver's line of vision, they Stand-on Electric Pallet Stacker should take the turning around workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to use inertia force to get the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Vehicle parking is not allowed under the list below problems.
1. Curves, narrow roads, railway crossings;.
2. Areas with a longitudinal incline more than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the challenge need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844